Comtrol AT Commands for SmartACFL Manual do Utilizador Página 65
- Página / 172
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Command Reference Manual
100722A
Conexant
3-45
3.2.5.6 +ETBM - Call Termination Buffer Management
This extended-format compound parameter controls the handling of data remaining in modem buffers upon call termination. It
accepts three numeric subparameters:
Syntax
+ETBM=[<pending_TD>[,<pending_RD>[,<timer>]]]
Defined Values
<pending_TD> Decimal number 0 specifying that disconnect will occur immediately and all buffered transmit data
will be discarded when the local DTE requests call disconnection.
<pending_RD> Decimal number 0 specifying that disconnect will occur immediately and all buffered receive data
will be discarded when the local DTE requests call disconnection.
<timer> Decimal number 0 specifying that the modem will not attempt to deliver the buffered data before
abandoning the attempt and discarding remaining data.
Reporting Current or Selected Values
Command: +ETBM?
Response: +ETBM: <pending_TD>,<pending_RD>,<timer>
Example: +ETBM: 0,0,0
Reporting Supported Range of Parameter Values
Command: +ETBM=?
Response: +ETBM: (<pending_TD> range),(<pending_RD> range), (<timer> range)
Example: +ETBM: (0),(0),(0)
3.2.5.7 \B - Transmit Break to Remote
In non-error correction mode, the modem will transmit a break signal to the remote modem with a length in multiples of 100
ms according to parameter specified. If a number in excess of 9 is entered, 9 is used. The command works in conjunction
with the \K command.
In error correction mode, the modem will signal a break through the active error correction protocol, giving no indication of the
length.
Syntax
\B<value>
Defined Values
<value> Decimal number corresponding to the selected option.
1-9 Break length in 100 ms units. (Default = 3.) (Non-error corrected mode only.)
Result Codes
OK If connected in data modem mode.
NO CARRIER If not connected or connected in fax modem mode.
Note:
When the modem receives a break from the remote modem, break is passed to the DTE as follows: In non-error
correction mode direct, the break length is passed; in non-error correction mode normal and in error correction mode, a 300
ms break is passed.
- AT Commands for SmartSCM 1
- SmartACF, and SmartACFL 1
- Contents 3
- Conexant 10
- 1. INTRODUCTION 11
- 1.2 REFERENCE DOCUMENTATION 12
- 2. SYNTAX AND PROCEDURES 13
- 2.3 Basic Syntax Commands 14
- 2.4 Extended Syntax Commands 15
- 2.5 Issuing Commands 18
- 2.6 Executing Commands 18
- 2.7 Modem Responses 18
- 3. DATA COMMAND SET 21
- 3.3 S-PARAMETERS 84
- 3.4 CELLULAR COMMANDS 98
- 3.5 RESULT CODES 102
- 4.1 FAX I/O PROCESSING 107
- 4.2 COMMANDS AND PARAMETERS 110
- 4.3 EXAMPLES 120
- 5. FAX CLASS 2 COMMANDS 123
- 5.6 EXAMPLE SESSIONS 142
- 6. VOICE COMMANDS 145
- 6.2 Voice Commands 148
- 7. INDEX 167
Manuais e produtos relacionados com Routers Comtrol AT Commands for SmartACFL
Routers Comtrol RM III V.90 Manual do Utilizador
(13 páginas)
(13 páginas)
Routers Comtrol RM II V.90 Manual do Utilizador
(6 páginas)
(6 páginas)
Routers Comtrol RM ISA V.34 Manual do Utilizador
(7 páginas)
(7 páginas)
BoConcept Bench 1590 manuales
Manuales del propietario y guías del usuario para No BoConcept Bench 1590.
Ofrecemos 1 manuales en pdf BoConcept Bench 1590 para descargar gratis por tipos de documentos: Manual de instrucciones
Comentários a estes Manuais